300-515 Dumps with Practice Exam Questions Answers
300-515 by CCNP Service Provider Actual Free Exam Practice Test
What is the duration, language, and format of Implementing Cisco Service Provider VPN Services (300-515 SPVI) Exam
- Language of Exam: English
- Duration of Exam: 90 minutes
- Validity: 3 years
- Format: Multiple choice
NEW QUESTION 37
Refer to the exhibit:
A network engineer is implementing an OSPF configuration Based on the output, which statement is true?
- A. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- B. IPv6 routing not enabled" is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
- C. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- D. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
Answer: A
NEW QUESTION 38
Refer to the exhibit.
Which statement about this configuration is true?
- A. 192.168.1.2 must be reachable by all routers participating in the mvpn-intranet MVRF.
- B. Router 1 will accept multicast routes with a route-target of 12:1.
- C. The MVRF must be configured on each router on the customer and service provider networks.
- D. Router 1 has statically defined thresholds for data MDT.
Answer: B
NEW QUESTION 39
An engineer is investigating an MPLS LDP issue. Which command should an engineer use on a Cisco IOS XE device to display the contents of the LFIB?
- A. show mpls ldp bindings
- B. show mpls forwarding-table
- C. show mpls ldp neighbors
- D. show mpls ldp labels
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mpls/command/mp-cr-book/mp-s2.html
NEW QUESTION 40
An engineer is troubleshooting an EoMPLS circuit on a Cisco IOS XR router interface that removes a VLAN from the distribution layer. Which configuration should the engineer apply in order to accomplish the task?
- A. interface GigabitEthernet 0/10.l2transport
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - B. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
rewrite ingress tag translate 1-to-1 dot1ad 10
symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - C. interface GigabitEthernet 0/10.10
encapsulation dot1q 10
rewrite ingress tag pop 1 symmetric
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 0/10.10
neighbor ipv4 10.10.10.2 pw-id 103588 - D. interface GigabitEthernet 0/10.10 l2transport
encapsulation dot1q 10
l2vpn
xconnect group 103588
p2p 103588
interface GigabitEthernet 2/10.10
neighbor ipv4 10.10.10.2 pw-id 103588
Answer: D
Explanation:
Section: Layer 2 VPNs
NEW QUESTION 41
Refer to the exhibit.
A customer carrier running MPLS VPN wants to utilize a backbone carrier to forward traffic and exchange VPNv4 prefixes between the two customer carriers networks depicted. Which two sets of routers must establish MP-iBGP sessions? (Choose two.)
- A. CC-PE-A and BB-PE-A
- B. BB-PE-A and BB-PE-B
- C. CC-PE-A and CC-PE-B
- D. BB-PE-A and BB-P-A
- E. CC-PE-A and CC-P-A
- F. BB-PE-A and CC-PE-B
Answer: B,C
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ias_and_csc/configuration/12-2sx/mp-ias- and-csc-12-2sx-book/mp-carrier-bgp.html
NEW QUESTION 42 
Refer to the exhibit. Which statement about this configuration is true?
- A. 192.168.1.2 must be reachable by all routers participating in the mvpn-intranet MVRF.
- B. Router 1 will accept multicast routes with a route-target of 12:1.
- C. The MVRF must be configured on each router on the customer and service provider networks.
- D. Router 1 has statically defined thresholds for data MDT.
Answer: B
Explanation:
Section: Layer 3 VPNs
NEW QUESTION 43
An engineer is troubleshooting AToM on an IOS XE router and receives an error when creating the xconnect.
Which command does he need to complete to create the xconnect in AToM?
- A. encapsulation mpls
- B. protocol none
- C. protocol 12tpv3
- D. encapsulation 12tpv3
Answer: A
Explanation:
Section: Layer 2 VPNs
NEW QUESTION 44
Which two BGP attributes prevent loops in a route reflector environment? (Choose two.)
- A. origin
- B. AS_PATH
- C. local preference
- D. cluster ID
- E. originator ID
Answer: D,E
Explanation:
Section: VPN Architecture
Explanation/Reference: https://www.ciscopress.com/articles/article.asp?p=2756480&seqNum=10
NEW QUESTION 45
Which condition must be met before an environment can support CSC?
- A. The CSC-CE must support OSPFv3.
- B. The CSC-PE and CSC-CE devices must be able to send labels to one another using BGP.
- C. The CSC-PE and CSC-CE must each be able to ping an interface in its respective global routing table.
- D. The CSC-PE and the CSC-CE must support IPv6.
Answer: B
Explanation:
Section: Layer 3 VPNs
NEW QUESTION 46
Which mechanism reduces the network flooding caused by host ARP learning behavior?
- A. BPDU guard
- B. root guard
- C. storm control
- D. ARP suppression
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/products/collateral/switches/nexus-7000-series-switches/white- paper-c11-735015.html
NEW QUESTION 47
Refer to the exhibit. If the two devices are operating normally, which two conclusions can you draw from this configuration? (Choose two.)
- A. PE1 labels the routes it learns from CE1 with the route-target 222:2 and shares them with its VPNv4 peers.
- B. CE1 must use OSPF to establish a neighbor relationship with PE1.
- C. The PE-CE routes between the devices are being exchanged by OSPF
- D. PE1 labels the routes it learns from CE1 with the route-target 111:1 and shares them with its VPNv4 peers.
- E. CE1 is supporting CSC.
Answer: B,C
NEW QUESTION 48
Refer to the exhibit.
Which result occurs when PE1 learns a new MAC address and all three PEs are enabled with EVPN native?
- A. The MAC address is entered into the CAM table only if it is learned on the native VLAN.
- B. The new MAC address is sent by BGP to PE2 and PE3 as a Type 2 BGP route.
- C. The MAC address is entered into the CAM table and is classified for use on the native VLAN
- D. A system notification is sent to the network administrator that triggers the manual configuration of the new MAC address on PE2 and PE3.
Answer: B
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-4/lxvpn/configuration/ guide/b-l2vpn-cg-asr9000-64x/b-l2vpn-cg-asr9000-64x_chapter_01011.html
NEW QUESTION 49
You try to configure MPLS VPN VRF Selection based on a source IP address on an interface that has VRF configured, but you receive an error.
Which action must you take to correct the problem?
- A. Remove the VRF from the interface.
- B. Configure static routes for the VRF.
- C. Add the IP address to the VRF table.
- D. Change the source IP address.
Answer: A
Explanation:
Section: VPN Architecture
Explanation/Reference:
Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/vrfselec.html
NEW QUESTION 50 
What is the effect of this configuration?
- A. An LSP virtual interface tunnel is created.
- B. The mroute table is cleared.
- C. A Cisco MPLS TE tunnel is generated with 192.168.1.2 as the source IP address of router 1.
- D. Router 1 accepts multicast routes with a tag of 12:1
Answer: D
NEW QUESTION 51
Refer to the exhibit. A network engineer is implementing an OSPF configuration.
Based on the output, which statement is true?
- A. OSPFv3 does not run for IPv4 on FastEthemet0/0 until IPv6 routing is enabled on the router and IPv6 is enabled on interface Fastfc.thernet0/0
- B. IPv6 routing not enabled is just an informational message and OSPFv3 runs for IPv4 on interface FastEthernet0/0 anyway
- C. In the ospfv3 1 area 1 ipv4 command, area 0 must be configured instead of area 1.
- D. OSPFv3 cannot be configured for IPv4; OSPFv3 works only for IPv6.
Answer: A
NEW QUESTION 52
An ISP provides a major client MPLS VPN for managed services. The MPLS engineering team needs to use the advanced VPN feature of selective VRF import so that only specific prefixes are present in the required VPNs.
Which aspect of this feature must the team consider?
- A. The routers that are imported in the VRF can be BGP and IGP routes, so other match conditions in the route map, besides communities, can be used.
- B. A route must pass the import route map first and then the route target import filter.
- C. The import-map command is applied under the PE interface that connects to the CE router.
- D. A route is imported into the VRF only when at least one RT that is attached to the route matches one RT that is configured in the VRF and the route is permitted by the import route map.
Answer: D
Explanation:
Reference: https://www.ccexpert.us/mpls/configuring-selective-vrf-import.html
NEW QUESTION 53
Refer to the exhibit.
An engineer has configured router 1 to provide shared services to clients behind router 2. To complete the implementation so that routes from router 1 are accepted, what must the engineer configure on router 2?
- A. with export route targets 301:202 and 101:102
- B. with export route targets 201:202 and 401:402
- C. with import route targets 101:102 and 202:201
- D. with import route targets 201:202 and 401:402
Answer: D
NEW QUESTION 54
Refer to the exhibit.
Which result occurs when PE1 learns a new MAC address and all three PEs are enabled with EVPN native?
- A. The MAC address is entered into the CAM table only if it is learned on the native VLAN.
- B. The new MAC address is sent by BGP to PE2 and PE3 as a Type 2 BGP route.
- C. The MAC address is entered into the CAM table and is classified for use on the native VLAN
- D. A system notification is sent to the network administrator that triggers the manual configuration of the new MAC address on PE2 and PE3.
Answer: B
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-4/lxvpn/configuration/ guide/b-l2vpn-cg-asr9000-64x/b-l2vpn-cg-asr9000-64x_chapter_01011.html
NEW QUESTION 55
Which two statements describe primary differences between MPLS Layer 2 and Layer 3 VPNs? (Choose two.)
- A. Layer 2 VPNs use IPsec tunneling, but Layer 3 VPNs use pseudowires to provide tunneling.
- B. Layer 2 VPNs use IPsec tunneling, but Layer 3 VPNs use L2TPv3 tunneling.
- C. Layer 2 VPNs use L2TPv3 tunneling, but Layer 3 VPNs use GRE tunneling.
- D. Layer 2 VPNs use AToM, but Layer 3 VPNs use MPLS/BGP.
- E. Layer 2 VPNs use BGP, but Layer 3 VPNs use VPLS.
Answer: C,D
NEW QUESTION 56
Which option is the primary purpose of central service MPLS VPNs?
- A. provide other service providers access to customer resources
- B. provide other service providers access to provider resources
- C. provide customer access to provider resources while ensuring customers cannot communicate directly
- D. provide the provider access to customer resources while ensuring customers cannot communicate directly
Answer: C
NEW QUESTION 57
Refer to the exhibit.
A customer carrier running MPLS VPN wants to utilize a backbone carrier to forward traffic and exchange VPNv4 prefixes between the two customer carriers networks depicted. Which two sets of routers must establish MP-iBGP sessions? (Choose two.)
- A. CC-PE-A and BB-PE-A
- B. BB-PE-A and BB-PE-B
- C. CC-PE-A and CC-PE-B
- D. BB-PE-A and BB-P-A
- E. CC-PE-A and CC-P-A
- F. BB-PE-A and CC-PE-B
Answer: B,C
Explanation:
Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/mp_ias_and_csc/configuration/12-2sx/mp-ias- and-csc-12-2sx-book/mp-carrier-bgp.html
NEW QUESTION 58
Refer to the exhibit.
Which statement about this configuration is true?
- A. 192.168.1.2 must be reachable by all routers participating in the mvpn-intranet MVRF.
- B. Router 1 will accept multicast routes with a route-target of 12:1.
- C. The MVRF must be configured on each router on the customer and service provider networks.
- D. Router 1 has statically defined thresholds for data MDT.
Answer: B
NEW QUESTION 59
When implementing Layer 3 MPLS VPNs on Cisco IOS/IOS XE PE routers, which PE-to-CE routing protocol requires a separate routing process to be created for each VRF?
- A. BGP
- B. RIPv2
- C. OSPF
- D. EIGRP
Answer: C
NEW QUESTION 60
Which optional information can be included with an IPv6 ping to support the troubleshooting process?
- A. IPv6 hostname
- B. IPv4 IP address
- C. source MAC address
- D. destination MAC address
Answer: A
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6/configuration/xe-3s/ipv6-xe-36s-book/ip6-mng-apps.html
NEW QUESTION 61
......
Implementing Cisco Service Provider VPN Services (300-515 SPVI) Certification Path
Implementing Cisco Service Provider VPN Services (300-515 SPVI) exam is affiliated with the CCNP Service Provider and Cisco Accredited Professional-Service Provider VPN Services Implementation certifications. This is the official prerequisite for this exam. However, the course, Integrating VPN Services from Cisco Service Provider, allows applicants to prepare for this exam and is highly recommended.
Official Training for Exam 300-515
The course for the Cisco 300-515 test called ‘Implementing Cisco SP VPN Services (SPVI) v1.0’ investigates issues about managing end-customer VPN environments which have been constructed over a common SP MPLS (Multiprotocol Label Switching) backbone. Also, you will have to finish tasks lined up in the practical labs so that whatever skills being covered will be reinforced. Subjects to look at during the training include MPLS VPN basic concepts, benefits, as well as classification, components for MPLS, and operations for the control plane alongside data planes concerning MPLS. Others are MPLS VPN tasks for routing that utilize VRF, MPLS VPNs for Layer 2 & Layer 3, implementing IPv6 MPLS VPN, IP Multicast associated VPNs and VPNs that concern shared services. More matters observed in the course include solutions lined up for the deployment of MPLS VPN that cross multiple SP domains and enhance how the network bandwidth is used. In general, there will be 5 days in which to take and complete this official training for 300-515 exam. Included is theory as well as the performance of tasks within a lab environment. A learner, in particular, can go for any of the three options for studying, including e-Learning, instructor-led, and virtual learning. On finalizing the course, one should be up to tasks in the following domains:
- Putting into practice operations for Multicast MPLS VPN targeting Layer 3 within an SP environment;
- Solving MPLS VPN-associated solutions targeting IPv6 surroundings.
- Troubleshooting VPN issues for Layer 2 in an SP environment;
- Implementing solutions for MPLS VPN that target IPv6 environments;
Free CCNP Service Provider 300-515 Exam Question: https://lead2pass.troytecdumps.com/300-515-troytec-exam-dumps.html