Exam Questions Answers Braindumps CQE Exam Dumps PDF Questions
Download Free ASQ CQE Real Exam Questions
For more info visit:
What is the duration of the CQE Exam
- Length of Examination: 5 hour 30 minutes
- Format: Multiple choices, multiple answers
- Number of Questions: 165
NEW QUESTION 45
A typical use for the optical comparator would be to measure
- A. Surface finish.
- B. Diameters of internal grooves.
- C. Depth of holes.
- D. Contours.
Answer: D
NEW QUESTION 46
A quality control program is considered to be
- A. A system of activities to provide quality of products and service.
- B. A summary of company quality control policies.
- C. A step by step listing of all quality control check points.
- D. A collection of quality control procedures and guidelines.
Answer: A
NEW QUESTION 47
A cause and effect diagram is also called which of the following?
- A. Boxplot.
- B. Histogram.
- C. Pareto diagram.
- D. Fishbone diagram.
Answer: D
NEW QUESTION 48
When requesting "worst case" design analysis, you expect the reliability group to
- A. Determine whether product requirements can be met with subassemblies assumed at their worst combination of tolerances.
- B. Assume all subassembly tolerances at their maximum limit.
- C. Analyze only those products failing to meet specification requirements.
- D. Analyze the worst rejects.
Answer: A
NEW QUESTION 49
The first and most important step, in establishing a good corporate quality plan is
- A. Determining customer requirements.
- B. Ensuring quality participation in design review.
- C. Determining manufacturing process capabilities.
- D. Evaluation vendor quality systems.
Answer: A
NEW QUESTION 50
In the failure rate model shown below, which one of the sections represents the period when catastrophic failures are likely to occur?
- A. All sections can experience catastrophic failure.
- B. A
- C. C
- D. B
Answer: A
NEW QUESTION 51
If the probability of a success on a single trial is 0.2 and 3 trials are performed, what is the probability of at least one success?
- A. 0.488
- B. 0.008
- C. 0.600
- D. 0.384
Answer: A
NEW QUESTION 52
A system was designed with 3 capacitors. When the system is first activated all capacitors are operating. The system continues to operate as long as at least 1 capacitor is operating. This is an example of
- A. A standby parallel system.
- B. A series system.
- C. An active parallel system.
- D. Redundancy.
Answer: C
NEW QUESTION 53
A bin contains 40 pills with a weight of 3.1 gm. each, 30 pills weighing 3.2 gms each and 10 pills weighing
3.3 gms each. The weight of an average pill is found from
- A. Option C
- B. Option B
- C. Option A
- D. Option D
Answer: D
NEW QUESTION 54
A typical use for the optical comparator would be to measure
- A. Surface finish.
- B. Diameters of internal grooves.
- C. Depth of holes.
- D. Contours.
Answer: D
NEW QUESTION 55
The distribution of a characteristic is negatively skewed. The sampling distribution of the mean for large samples is:
- A. Positively skewed.
- B. Lognormal.
- C. Negatively skewed.
- D. Approximately normal.
Answer: D
NEW QUESTION 56
The basic elements of an ultrasonic test systems do NOT include which of the following?
- A. A test object.
- B. A laser beam.
- C. A transducer.
- D. An electronic system.
Answer: B
NEW QUESTION 57
The AQL for a given sampling plan is 1% this means that
- A. The producer takes a small risk of rejecting product which is 1% defective or better.
- B. All lots are 1% defective or better.
- C. The average quality level of the plan is 1%.
- D. All accepted lots are 1% defective or better.
Answer: A
NEW QUESTION 58
The use of 100% inspection normally means
- A. That the lowest over-all quality costs have been considered.
- B. That selected characteristics have been evaluated against specified standards.
- C. That there will be an opportunity to rework any product deemed to be outside of specifications.
- D. That the final customers will not experience defective product.
Answer: B
NEW QUESTION 59
The probability of accepting a lot of unacceptable quality is known as
- A. 1-beta.
- B. Producer's risk.
- C. Beta risk.
- D. Alpha risk.
Answer: C
NEW QUESTION 60
A comprehensive corrective action program is initiated at a large company. Input for CARs are received from customers, internal and external audits, material review reports and other sources. Which two of the following groups would usually administer and control the CAR process?
I. Management review team.
II. Quality department.
III. Corrective Action Board.
IV. Material Review Board.
- A. III and IV only
- B. I and III only
- C. II and III only
- D. I and II only
Answer: B
NEW QUESTION 61
Which of the following list of basic NDT techniques are X ray types?
- A. Ultrasonic / Optical.
- B. Thermal / Radiation.
- C. Radiation / Image generation.
- D. Electromagnetic / Thermal.
Answer: C
NEW QUESTION 62
......
Latest ASQ CQE Real Exam Dumps PDF: https://lead2pass.troytecdumps.com/CQE-troytec-exam-dumps.html